- 您现在的位置：买卖IC网 > Sheet目录976 > DM164128 (Microchip Technology)KIT DEV PICDEM TOUCH SENSE 2
PICDEM Touch Sense 2 Demo Board User’s Guide
FIGURE 4-2:
TOUCH SENSE 2 DEMO BOARD, WITH TOP ACRYLIC
COVER REMOVED TO SHOW SENSORS
Nine of the A/D channels are used to monitor the numeric keypad switches (S1 through
S12 and S21 through S27), arranged in a 4x5 array. Each “switch” is composed of
interleaved conductors from two channels. The location of the touched key is
determined by a simultaneous capacitance change on any two channels.
Four channels are used to monitor the directional keypad. The sensor consists of four
arrow shaped, dual capacitive touch pads, oriented at the four cardinal compass points
(N, E, S and W), with capacitive touch pads at the adjacent four compass points (NE,
SE, SW and NW) and in the center. Touch events on the cardinal points causes a
capacitance change in the corresponding channel. Touches between the cardinal
points, or in the center, are interpolated from simultaneous changes on two adjacent
channels, or all four channels, respectively.
Two channels are used to monitor the touch slider, S14. The slider is composed of two
large and adjacent capacitive touch pads, tapering from one side to the other and in
opposite directions. The location of a touch event on the slider is determined by the
differential change in capacitance between the channels.
The remaining A/D channel is used to monitor the demo board’s “soft” power switch,
S20; this is an interleaved capacitive touch pad similar to those in the numeric keypad.
When power is applied to the Touch Sense 2 Demo Board, the microcontroller
immediately initializes the demo application and starts in Full-Power mode. When the
power switch is pressed and held for approximately 3 seconds, the microcontroller
goes into Low-Power Sleep mode, monitoring S20 at intervals of 50 milliseconds. A
touch event on S20 causes the application to wake again to full-power operation.
When an event occurs, the application firmware also provides feedback by activating
one or more LEDs at that location. A total of 61 LEDs are driven directly by the
microcontroller through pins on PORTC, PORTD, PORTE and PORTG. The LEDs for
the numeric keypad are driven as a 4x5 matrix from PORTE, using 5 lines to source
current and four to sink current. Individual LEDs are used for the directional keypad and
the power switch.
The linear LED display on the touch slider is driven in a method similar to those of the
numeric keypad, using a 4x4 matrix on PORTD. Each node has two LEDs, connected
in forward and reverse-biased pairs. To light a specific diode in each pair, the row and
column ports are toggled to act as current sources or sinks, causing one diode or the
other to be properly biased.
In addition to visual feedback, the demo board also provides audible feedback for each
touch event on the numeric keypad. An audio signal is generated using one of the
microcontroller ’s PWM module, and directly drives the piezo speaker BZ1 through pin
RG7.
DS51748A-page 20
? 2008 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DM183026-2
KIT EVAL MTOUCH CAPACTIVE
DM183026
KIT EVALUATION PIC16F/PIC24F
DNGL
GROUND LUGS 1 1/8X1 3/16"
DO KA TYPE 21-5M
FM3 CABLE W/CONN 5M
DO061B-B
RELAY SSR 1A MINI-SIP
DP4RSC60E60B8
RELAY SSR CONTACT 48VDC 60A 32V
DPA4119
RELAY SSR 3.5-10VDC INPUT 16 DIP
DR-25-3-0-SP
HEATSHRINK 3"X150' SPL BK
相关代理商/技术参数
DM164130-1
功能描述:开发板和工具包 - PIC / DSPIC F1 Eval Platform
RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM164130-1
制造商:Microchip Technology Inc 功能描述:MCH1P - SKU FOR APRIL BUNDLE
DM164130-10
功能描述:开发板和工具包 - PIC / DSPIC F1 PSMC 28-PIN EVAL BOARD PLATFORM
RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM164130-2
功能描述:子卡和OEM板 F1 BLDC Motor Add-On RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
DM164130-3
功能描述:开发板和工具包 - PIC / DSPIC PICkit 28-Pin LIN Demo Board
RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM164130-4
功能描述:开发板和工具包 - PIC / DSPIC PICkit 44-Pin Demo Board RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM164130-4
制造商:Microchip Technology Inc 功能描述:PICKIT 44-PIN DEMO BOARD
DM164130-5
功能描述:BOARD EVAL F1 LV PIC21F1/PIC16F1 RoHS:否 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:XLP™ 产品培训模块:Blackfin® Processor Core Architecture Overview
Blackfin® Device Drivers
Blackfin® Optimizations for Performance and Power Consumption
Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板，软件，4x4 键盘，光学拨轮，QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA